Model NO.: YR-V-20180904A
Customized: Customized
Trademark: Yurui
Transport Package: Bulk Packing
Specification: 560CBM
Origin: China
HS Code: 8474809010
Model NO.: YR-V-20180904A
Customized: Customized
Trademark: Yurui
Transport Package: Bulk Packing
Specification: 560CBM
Origin: China
HS Code: 8474809010
Equipment Parameter
|
OutputÂ
|
2 million - 30 million sqm/year (based on thickness 9.5mm)
|
|
FuelÂ
|
coal; natural gas; diesel; heavy oil, etc
|
|
Technology
|
hot air; heat transfer oil/thermal oil
|
|
Width
|
1200mm, 1220mm
|
|
ThicknessÂ
|
6mm to 22mmÂ
|
|
LengthÂ
|
1500mm-3000mm
|
|
Raw materialÂ
|
Natural gypsum powder, phosphorus gypsum powder, desulfurized gypsum powder
|
Flow chartÂ
Raw material request
| Raw materials | Item | Specification |
|
Calcined gypsum powder |
Fineness |
0.2mm, <10% 0.2mm, Remnant <10% |
|
Initial set time |
3.5-5.5 3.5-5.5 minutes |
|
|
Final set time |
7.5-10.5 7.5-10.5 minutes |
|
|
Crystal water |
4.5%-5% | |
|
Half-water gypsum powder |
>65% | |
|
(2) Bending strength (2 hours) |
1.8 Mpa | |
|
Paper |
Weight |
190-220g/ |
|
Thickness |
0.36-0.4mm | |
|
Air permeability |
0.85-1.6μm/pas | |
|
(Cobb) Water absorption( Cobb ) |
15-30g/ | |
|
Tensile strength |
12.5 KN/m, 3.5 KN/m Portrait 12.5 KN/m, transverse 3.5 KN/m |
|
|
Transverse expansion and contraction |
<2% | |
|
Moisture |
10%±2 | |
|
Denaturized starch |
Content of the starch |
>70% |
| Moisture | 11%-13% | |
| PH | 6.5-7.5 | |
| Protein | <0.3% | |
|
20ºC-40ºC Solubility in 20ºC-40ºC water |
73%-78% | |
|
Foaming agent |
Condensate |
>30% |
|
Ligarine |
<3% | |
|
Inorganic salts |
>2.5% | |
| PH | 7-9 | |
|
water Water |
PH | 6.5-7.5 |
Factory view
Equipment advantageÂ
1. Fine workmanship, high precision, reliable quality, beautiful appearance
2. Accurate dosing for each raw material. Starch mixing tank use stainless steel, with long service life and low corrosive. The foaming agent reserve tank is made of stainless steel. Foaming system adopts domestic advanced technology - Dynamic and static foaming system, ensuring the finished board is lightweight, good bending strength and saving much cost.
3. The cutting machine uses dual-serve motor, only 1 mm gap between cutting saw, saving cost .
4. Drying system: using heat conduction oil furnace as heat source, the hot oil will be exchanged to hot air by the fin type heat exchanger, then the hot air enters the drying room through the fan, to work together with the heat conduction oil pipe to dry the gypsum board. There are totally 3 drying zones, can perfectly finish the drying curve, avoid the over-burning or not dry enough. This technology is environmental, energy saving, high thermal efficiency, process parameters and is easy to control.
5. High electrical automation degree, low failure rate, less workers.
6. Forming system: forming belt 14mm thick, can improve the flatness of gypsum board. The wet board cutting machine uses frequency conversion code cutting technology, so can ensure the length tolerance to be mm.
Labor requirements
| System | Workers needed |
| Dosing.mixing material system | 2 / 1 workers/shift |
|
Laser Consumables For Bystronic Ceramic Nozzle Holder,Laser Head Parts,Laser Cutter Components,Nozzle Holder Changzhou Cewoo Equipment Co.,Ltd , https://www.cewoocut.com |